Faults after updating modules with UCDS

Resolving problems with software and hardware

Модератор: DanMc85

Ответить
xnm374
Сообщения: 6
Зарегистрирован: 09 янв 2020, 21:34

Faults after updating modules with UCDS

Сообщение xnm374 »

Hello, I'm new here.
I recently updated all the modules on my 2017 ranger using the update wizard.
Since then I have faults in the BCM and RCM

The fault is B11D8 crash event occurred.

Can somebody please help me resolve this, Thanks. Jo

silvercircle
Сообщения: 16
Зарегистрирован: 14 ноя 2017, 21:57
Откуда: Germany

Re: Faults after updating modules with UCDS

Сообщение silvercircle »

Change the value in the direct config from true to false.

xnm374
Сообщения: 6
Зарегистрирован: 09 янв 2020, 21:34

Re: Faults after updating modules with UCDS

Сообщение xnm374 »

I cannot find this option

silvercircle
Сообщения: 16
Зарегистрирован: 14 ноя 2017, 21:57
Откуда: Germany

Re: Faults after updating modules with UCDS

Сообщение silvercircle »

start ucds, start direkt configuration, take your modell an open the bcm contol unit read from car then take a look an alle parameters. by an Focus ist the chrash parameter Nr. 35 or so. by other modells ??? make the same in the other control unit.

xnm374
Сообщения: 6
Зарегистрирован: 09 янв 2020, 21:34

Re: Faults after updating modules with UCDS

Сообщение xnm374 »

That option isn’t visible in the ranger bcm

silvercircle
Сообщения: 16
Зарегистрирован: 14 ноя 2017, 21:57
Откуда: Germany

Re: Faults after updating modules with UCDS

Сообщение silvercircle »

when i start my ucds, i find in direct config, bcm (FU5T-) under point 115 Alarms 01 DE 00 "crash enable cfg (disabled) and underneth crash spinout ... there gives 3 different types of bcm modules they are build in a ranger, you must try which one is the correct one and search. i dont know whether it is correct but ucds has is no manual, you can only try.

xnm374
Сообщения: 6
Зарегистрирован: 09 янв 2020, 21:34

Re: Faults after updating modules with UCDS

Сообщение xnm374 »

Hello, thanks for the reply. I have tried this and still no luck.

silvercircle
Сообщения: 16
Зарегистрирован: 14 ноя 2017, 21:57
Откуда: Germany

Re: Faults after updating modules with UCDS

Сообщение silvercircle »

have you tried to clear crash data in normal mode ? you take the picture from ranger and go to the special procedures. here is a point to clear all faults in register rcm.

xnm374
Сообщения: 6
Зарегистрирован: 09 янв 2020, 21:34

Re: Faults after updating modules with UCDS

Сообщение xnm374 »

Yes I have tried that, running out of things to try now

xnm374
Сообщения: 6
Зарегистрирован: 09 янв 2020, 21:34

Re: Faults after updating modules with UCDS

Сообщение xnm374 »

Fixed, many thanks to darkleo! He reverted software back to before update!

Ответить