Change IPC Firmware Lincoln MKZ to Mondeo MK5/Fusion

[peterpro]

other photos of configurations

[AmigaSurfer]

BUT you say either: BTW, there is a call-back 20P06 for Mondeo MK5 equipped with IPC firmware JS7T-14C026-AJB and KS7T-14C026-AJD. If you have updated an IPC with older firmware to one of this firmwares, I suggest to make this change by hand.
IPC DE06 "(not used) *DO NOT USE (AutoHigh Beam Telltale)" must be changed from Disabled to Enabled. It's bit 30 in IPC DE06
Here is the strange....this voice is present only in DE06 of all IPC (KS7T-J* and KS7T-G*) but not in KS7T-B**, that in fact i must use to edit the other option. So something confusing here... attached images
With UCDS how did you wrote this values in IPC?

I used IPC (JS7T-*) to change this parameter. I think regardless of witch module you select, if the parameter is visible it will change always the same bit.

And last....upgraded with success from GS7T-14C026-AJE to KS7T-14C026-AJD, all went ok, ipma already to FS7T-14G019-SJ, traffic sign works, but i loose the driver alert graphics system. I have the option ticked in Assistance menu of IPC (tried to enable/disable from there), but in old calibration there was some graphics with the cup of coffee that was grey under 65km/h and then got colored over that speed. If you want to check manually the driver alert status, in the last settings menu (vehicle or display... i cannot remember exactly) you could pump that graphics. Now is not visible any more and even trying to zig-zag during motion did not engaged the graphic alert itself that before was prompted! i tried to drive for 400km over 65km/h but still no graphics. traffic sign and lane assist are working as expected. Some tips?
Thanks a lot!

The graphical display with the coffee cup is gone with KS7T-14C026-AJD and newer, but the driver alert should still work. Do not drive zig-zag like drunken to provoke the driver alert message. Don't touch the steering wheel much and let the car overrun the middle line of the motorway by itself in a very small angle. Let the lane assist systen working without much interaction from you. If you do this two or three times I think you must get an driver alert message.

[peterpro]

Thank's a lot for your explaining!
Otherwise....at the end of a week of testing with KS7T IPC....i downgraded again to the last GS7T that was before!
Drive alert and auto high beam telltale returned without modify direct config, i really like my traffic sign position and don't care for different brake graphics (i prefer the old one) and little car in lane assist! In fact for me there's no need at all to pass over new IPC MY. All is good as now.
I mainly upgraded to KS7T because i've seen that Chemikus have done some beatiful graphics mod to IPC....but i think that all of that mod could be done even in GS7T- AJE firmware!
I will ask him

[Egozo]

Can anyone recommend the calibrations for a change in the Ford Fusion 2018 (ipc js7t-10849-ga) fw like on Lincoln?

[Egozo]

And last....upgraded with success from GS7T-14C026-AJE to KS7T-14C026-AJD, all went ok, ipma already to FS7T-14G019-SJ, traffic sign works, but i loose the driver alert graphics system. I have the option ticked in Assistance menu of IPC (tried to enable/disable from there), but in old calibration there was some graphics with the cup of coffee that was grey under 65km/h and then got colored over that speed.

how many signs are reflected in this fw? Only speed limiters ?)

[sjkhsl]

Can you give me the ls7t-14c026-ajc
LS7T-14C026-BJC
LS7T-14C088-AJC
Ls7t-14c088-bjc firmware?
And IPMA firmware!
naxinglong@gmail.com

[Renebo]

Can some of you tell me what files i need for this layout, on my Smax MY2018? Thank you Im not willing to risk my traffic signs tho

[Neron-ek]

Hello

Can somebody help me to selct correct IPC firmware with central EU languages.
My IPC : Strategy - GS7T-14C026-GC
Calibration - GS7T-14C088-GC
I tried:
Strategy: HB5T-14C026-CA
Calibration: HB5T-14C088-CA

but then have IPC error U-0401 incorrect data recieved from ECM an electric brake indicator need 20 second to go off after ignition on

[maniutek]

What files should I upload to get the road signs on the left, as in the picture? I have a Mondeo MK5 equipped with IPC firmware JS7T-14C026-AJB and IPMA FS7T-14G025-SF

[Wyrkan]

What files should I upload to get the road signs on the left, as in the picture? I have a Mondeo MK5 equipped with IPC firmware JS7T-14C026-AJB and IPMA FS7T-14G025-SF

You only Need to enable it with ucds

[Bullets4all]

Hello
I have a Mondeo MK5 2.0 TDCI from 2015 and I want to know if a firmware update can be made to the LS7T version?
Or is it just for the Ford Mondeo 2020 manufacture?
Thank you

[maniutek]

What files should I upload to get the road signs on the left, as in the picture? I have a Mondeo MK5 equipped with IPC firmware JS7T-14C026-AJB and IPMA FS7T-14G025-SF

You only Need to enable it with ucds

Do you remember which parameter is responsible for it?

[Bullets4all]

Destiny a 2015 Monedo with ACC and reading road signs but I heard that you can write an IPC software on the S-MAX that has the option to automatically adjust the speed according to the road signs "AUTOLIM" ISA System. Can someone help me with a tutorial and what files to

phpBB [youtube]

https://www.youtube.com/watch?v=2DCrlEo55Ic

[dragunov]

What files should I upload to get the road signs on the left, as in the picture? I have a Mondeo MK5 equipped with IPC firmware JS7T-14C026-AJB and IPMA FS7T-14G025-SF

You only Need to enable it with ucds

How exactly?

Thanks!

[maniutek]

Exactly how ???