Страница 1 из 1

Kuga MK2 PAM Upgrade

Добавлено: 31 окт 2020, 15:51
grobi152
Hello,
I would like to install the PAM module from 2018 on the Kuga MK2 from 2016, is that possible? And if so, how do I get the communication error to the power steering fixed?
Вернуться к началу

Re: Kuga MK2 PAM Upgrade

Добавлено: 22 дек 2020, 12:00
Tino123
grobi152 писал(а): 31 окт 2020, 15:51 I would like to install the PAM module from 2018 on the Kuga MK2 from 2016, is that possible?
Hast du es inzwischen hinbekommen? Bei mir gehts nicht, UCDS lädt die AS-Built zwar von Ford, speichert aber absolut nichts im neuen PAM. Im neuen PAM standen vom Spenderfahrzeug 12 Sensoren, ich habe aber nur 8. Darum gabs diverse Fehlermeldungen. Ändere ich von 12 auf 8 oder 10 Sensoren sind die Fehler zwar weg, aber im Sync 3 werden dann nur noch die hinteren Sensoren angezeigt und vorne fehlen sie vollständig. Ich hätte ja gerne mal die Einstellungen die da alle rein müssen damit das PAM von 2018/2019 in einem 2016er Vorfacelift laufen. Hab dazu hier aber bisher keinerlei Hilfe bekommen bis auf den Hinweis die AS-Built zu laden was aber sich nicht im PAM speichern lässt.

Have you done it, in the meantime? With me gehts not, UCDS loads the AS-Built, indeed, from Ford, however, stores absolutely nothing in the new PAM. In the new PAM 12 sensors stood from the donator's vehicle, however, I have only 8. Therefore gabs various error messages. If I change from 12 to 8 or 10 sensors, indeed, the mistakes are away, but then in the Sync 3 only the rear sensors are indicated and in front they are absent completely. I would have with pleasure sometimes the settings there everything purely must run with it the PAM from in 2018/2019 in the 2016th prefacelift. If no help has got in addition here, however, up to now up to the tip to load the AS-Built what cannot be stored, however, in the PAM.

Re: Kuga MK2 PAM Upgrade

Добавлено: 24 апр 2021, 23:30
grobi152
Hallo,
Ich bin schon etwas weiter, die Steuergeräte brauchen ein Update. Dann könnte es möglicherweise mit dem neuen wie mit
dem modifizierten PAM funktionieren. Aber so bin ich noch nicht. Ich habe jetzt die neueste Software auf dem BCM und PSCM
drauf, habe jetzt noch Einstellungsprobleme beim BCM.Dann wollte ich das PAM machen.

Re: Kuga MK2 PAM Upgrade

Добавлено: 25 апр 2021, 09:21
Tino123
Welche Steuergeräte brauchen denn ein Update? Ich hab den Kuga inzwischen zwar verkauft und nun einen Kuga Vignale von 12/2019 wo wirklich alles drin ist. Aber der alte Kuga hat eigentlich alles an Updates drin was es gab. Aktueller geht nicht. Also daran kann’s bei meinem nicht gelegen haben. Ich hab aber das PAM-Modul was da rein sollte noch liegen falls du brauchen kannst. Das ist von einem Kuga von Ende 2018 glaube ich, bin gerade nicht zu Hause um nachzuschauen.

Re: Kuga MK2 PAM Upgrade

Добавлено: 26 апр 2021, 21:34
grobi152
Hallo,

ich habe selbst auch eins vom 2019er hier liegen,aber die Umbauanleitung bezog sich ja auf das alte mit anderer Software.
das Habe ich noch nicht ausprobiert,allerdings hat der der Kollege,der das umgebaut hat,den Kuga auch verkauft.