i have the latest UCDS installed.
Apim HS7T-14G371-FAE.
i tried updating with
GB5T-14G376-AA
1U5T-14G374-DA
1U5T-14G375-HA
GB5T-14G379-AA
JB5T-14G379-BA
Bootloader did go, erasing flask block 1, 2 and 3 did go oke, it said erasing flash finished.
Programming flash block 1 to 5 starts, but then....
Set new address failed.
Failed to programming flash! Error: Conditions not Correct [0x22]
Ended with an apim which doesn't come up again, i keep a black screen.
uuv file said, GB5T-14G374-CB was current version befote i updated (made an uuv file before i start update)
S i tried to go back to what is was.
GB5T-14G376-AA
GB5T-14G374-CB
GB5T-14G375-FA
GB5T-14G379-AA
GB5T-14G379-BA
same problem
tried then...
GB5T-14G376-AA
GB5T-14G374-CB
GB5T-14G379-AA
GB5T-14G375-CA
GB5T-14G379-BA
same problem.
Ten i tried Forced Programming with enable sleep all modules. Also no luck... this option keeps on "waiting"
Please help. I have a lot of experience with the UCDS but this time, i can't come to a solution.
Sync3 black screen after trying update
Модератор: DanMc85
-
- Сообщения: 10
- Зарегистрирован: 24 ноя 2016, 09:57
-
- Сообщения: 10
- Зарегистрирован: 24 ноя 2016, 09:57
Re: Sync3 black screen after trying update
More info,
i tried only
GB5T-14G376-AA
GB5T-14G374-CB or 1U5T-14G374-DA or HB5T-14G374-CA
all get the same error.
Set new address failed.
Failed to programming flash! Error: Conditions not Correct [0x22]
I tried the other files seperate with the boatloader and they go without a problem.
i tried only
GB5T-14G376-AA
GB5T-14G374-CB or 1U5T-14G374-DA or HB5T-14G374-CA
all get the same error.
Set new address failed.
Failed to programming flash! Error: Conditions not Correct [0x22]
I tried the other files seperate with the boatloader and they go without a problem.
-
- Сообщения: 10
- Зарегистрирован: 24 ноя 2016, 09:57
Re: Sync3 black screen after trying update
@kroligoff do you have a solution/suggestion for me?
- kroligoff
- Сообщения: 1497
- Зарегистрирован: 16 янв 2013, 11:38
Re: Sync3 black screen after trying update
Conditions not Correct [0x22] give error if not have ignition , low voltage or other issue who not give access to programming mode
-
- Сообщения: 10
- Зарегистрирован: 24 ноя 2016, 09:57
Re: Sync3 black screen after trying update
Batterie is only 2 years old. I always charge the batterie 100% full with a Ctek charger before i programm with UCDS.
I have keyless entry.
Strange thing also is,
this combination gets the error.
GB5T-14G376-AA
GB5T-14G374-CB or 1U5T-14G374-DA or HB5T-14G374-CA
this combination, programming works
GB5T-14G376-AA
1U5T-14G375-HA or GB5T-14G379-AA or JB5T-14G379-BA
i tried enable sleep all modules on and off, makes no difference.
I have keyless entry.
Strange thing also is,
this combination gets the error.
GB5T-14G376-AA
GB5T-14G374-CB or 1U5T-14G374-DA or HB5T-14G374-CA
this combination, programming works
GB5T-14G376-AA
1U5T-14G375-HA or GB5T-14G379-AA or JB5T-14G379-BA
i tried enable sleep all modules on and off, makes no difference.
-
- Сообщения: 7
- Зарегистрирован: 16 ноя 2019, 01:13
Re: Sync3 black screen after trying update
has anyone else had this issue? i need to flash my APIM with the same files a @johoo and don't want to wind up with a mess
need to use the below
GB5T-14G376-AA
1U5T-14G374-DA
1U5T-14G375-DA
GB5T-14G379-AA
JB5T-14G379-BA
need to use the below
GB5T-14G376-AA
1U5T-14G374-DA
1U5T-14G375-DA
GB5T-14G379-AA
JB5T-14G379-BA
-
- Сообщения: 14
- Зарегистрирован: 05 янв 2020, 15:32
Re: Sync3 black screen after trying update
Probably dead module.