How to setting xenon headlamps?

[Speedo]

Hallo!

I mounted in my S-Max 2008 xenon lights (orginally was halogen), working. Many later I try to install curves lighting (H1 bulbs in the interior corner of lamp), I bought used HCM module, electric instalation. After instalation in my auto curves lighting working perfectly. One day I was reflashing my HCM module (just for fun) and... curves lighting DEAD - Error U2101 - wrong module configuration or something - I must have programming headlamps alignment but... I can't beacuse I have three additional errors - B11A2 - Master Exterior Light Switch, B1D65 - Right Headlamp Swivelling Motor Circuit and B1D64 - Left Headlamp Swivelling Motor Circuit. Anyone knows how to reprogramming my HCM module? How to make headlamps alignment without those errors?

Best regards
Speedo

[kroligoff]

You try rewrite asbuild on BCM?

[Speedo]

Oryginal fabric as-built or my modified? My modified many many times, fabric I haven't tried yet.

[Speedo]

OK, tomorrow I write fabric as-built, modified, to bcm, to ipc, not working. After reset module HCM working few seconds, then error "incorrect module configuration" and not working. When I erase DTC curves light lighting, left-right every time.

Or it may be my master light switch (hallogen version)? Try to buy from xenon version? What do you think?

[kroligoff]

Please write here HCM HW and SW name version.
From UUW file (update wizard session)

[Speedo]

Thank you for your interesting!

HCM HW: 6M21-13K031-AD
SW: 6M21-14C084-AD

[Speedo]

OK, today I installed light switch from xenon version - no reaction.

I all day (another) programming, flashing, changing asbuilt, cancelling errors, calibrating, using els27, ucds, ids itd. itp.

What has changed:

Headlights motors working after ignition - no motors DTC, no light switch DTC.

Actually 4 DTC's (3 new, 1 old):

1. HCM module configuration incompatible
2. Missing calibration file
3. Front level position sensor
4. Rear level position sensor

DTC from sensors normally - I haven't sensors
Calibration must be done - but errors block process.
Module configuration incompatible? I don't know.

Curves light of course not working :/

[kroligoff]

You try install xenon parameter on asbuilt ?


Calibration must be done - but errors block process. - What this error?

[Speedo]

Xenon parameter (Adaptative Bi-Xenon lights) on as-built I have all time, without that my lights not working

During calibration IDS writing "failed because still DTC'S on HCM". Does not specify what errors.

[zaqik]

xenon parameter: GDL system (not bi-xenon)

[Speedo]

If I set GDL - tragedy, many many errors - CCII, power steering...

[zaqik]

WF0SXXGBWS8G21213 ... Smax with xenon from factory ... see to XML file (configuration)

[Speedo]

Almost the same as mine except GDL

I guess the key is here: "Missing calibration file"

Where you take and how to load HCM calibration file?

Simply insert my HCM to fabric-xenon auto and calibrating, but I haven't such a car nearby...

[zaqik]

you probably deleted parameters from HCM ... you need IDS for auto-callibration (or focom with miniVCM or forscan with ELM)

[Speedo]

you probably deleted parameters from HCM ... you need IDS for auto-callibration (or focom with miniVCM or forscan with ELM)

YES, I know, I personally deleted this parameters

I have IDS, I have ELM but I cant't calibration my HCM, because I have errors from missing level sensors...

The level sensor installation has 3 wires: +5V, GND and Signal. If I junction +5V and Signal this work? Or HCM burning?