UCDS Forum

But the engine is well, no? Do you need make a rollback? Or restore PCM Configuration?

Engine is OK, set back to 140PS via UCDS, updating pcm via IDS aswell had no effect so FORD had to do it to receive proper values for pcm.

For Change SMAX 140>163 like Kuga2 Procedures!

Possible even the current procedures will apply now

This weekend i can test it!

Kroligoff do you can explain more, please!

I dont have IDS, i have ucds cable and 2 elmconfig.

I need instruction step by step!

I have the ucds cable and it is operating in windows 7Pro 32 bits!
The firmware version 12, and the ucds version is 1.24.019.

In windows 8.1Pro 64 bits one error appear that the laptop is a virtual machine!

You Run 8.1 in Virtual Mashine? We disabled run UCDS in virtual mashines.

I write instruction

1. Check Vehicle VIN on http://www.ETIS.ford.com for need engine DW10C 2. On Asbuilt Editor Paramtere 5 (ENGINE) Change to ... DW10C 150PS ... 3. Write Asbuilt to BCM
4. Go to Focus 3 or Kuga 2 Section
PCM\TCM Reprogramming
4.1 Press CCC Learning Diesel 6. Clear DTC

It is 100% working in Mondeo MK4 and S-Max/Galaxy ?


Tomek

this is a rollback method or upgrade?

i'm also insteresting in upgrade 140-163 by these method??? how about ff3 95hp-115hp??
no ids needed???

kroligoff писал(а):You Run 8.1 in Virtual Mashine? We disabled run UCDS in virtual mashines.

I write instruction

My laptop is a physical laptop, not virtual. I install the drivers and work fine, the device manager is ok, i install the ucds software like administrator a work fine, but when i try to open ucds program, the error appear.

Tomorrow at morning i will test it!

Thanks for all Kroligoff!!!

phoenix241 писал(а):Tomorrow at morning i will test it!

OK I wait for any informations

Good morning! I change the engine type to 150Ps, i write configuration, and i select ccc learning in kuga2. After this i clear all dtcs with ucds and with forscan.

But now i have a new error.

In module PBM: code 2101 - Control Module Configuration Incompatible

Parking Brake Control Module

phoenix241 писал(а):Good morning! I change the engine type to 150Ps, i write configuration, and i select ccc learning in kuga2. After this i clear all dtcs with ucds and with forscan.

Now You have 163 PS ? Test it in Forscan -- PID --CET
PS 140 is about 340-345 Nm and 163 after switching to a minimum of 370 Nm

phoenix241 писал(а): But now i have a new error.
In module PBM: code 2101 - Control Module Configuration Incompatible
Parking Brake Control Module

We must wait for solution by Kroligoff

leszcz33 писал(а):

phoenix241 писал(а):Good morning! I change the engine type to 150Ps, i write configuration, and i select ccc learning in kuga2. After this i clear all dtcs with ucds and with forscan.

Now You have 163 PS ? Test it in Forscan -- PID --CET
PS 140 is about 340-345 Nm and 163 after switching to a minimum of 370 Nm

phoenix241 писал(а): But now i have a new error.
In module PBM: code 2101 - Control Module Configuration Incompatible
Parking Brake Control Module

We must wait for solution by Kroligoff

Hi leszcz33,

First: the car is not mine, it is of my friend, him live at 100 km.

Second: i dont known where is PID-CET, if you can send me one photo or instructions, the next time i will view it.

But leszcz33, when i read the configuration through ucds or elmconfig, the bcm show 150 PS.

Hi,
1. Ok, Asbuilt is original on vehicle or modifed before? You read first and vehicle have parameter 150, before you modifications?

2. Now this vehicle set 163ps?