Sync3 black screen after trying update

Resolving problems with software and hardware
Не в сети
Johoo
Сообщения: 10
Зарегистрирован: 24 ноя 2016, 09:57
Благодарил (а): 1 раз. Поблагодарили: 0 раз.
i have the latest UCDS installed.

Apim HS7T-14G371-FAE.

i tried updating with

GB5T-14G376-AA
1U5T-14G374-DA
1U5T-14G375-HA
GB5T-14G379-AA
JB5T-14G379-BA

Bootloader did go, erasing flask block 1, 2 and 3 did go oke, it said erasing flash finished.

Programming flash block 1 to 5 starts, but then....

Set new address failed.
Failed to programming flash! Error: Conditions not Correct [0x22]

Ended with an apim which doesn't come up again, i keep a black screen.

uuv file said, GB5T-14G374-CB was current version befote i updated (made an uuv file before i start update)

S i tried to go back to what is was.

GB5T-14G376-AA
GB5T-14G374-CB
GB5T-14G375-FA
GB5T-14G379-AA
GB5T-14G379-BA

same problem

tried then...

GB5T-14G376-AA
GB5T-14G374-CB
GB5T-14G379-AA
GB5T-14G375-CA
GB5T-14G379-BA

same problem.

Ten i tried Forced Programming with enable sleep all modules. Also no luck... this option keeps on "waiting"

Please help. I have a lot of experience with the UCDS but this time, i can't come to a solution.
Не в сети
Johoo
Сообщения: 10
Зарегистрирован: 24 ноя 2016, 09:57
Благодарил (а): 1 раз. Поблагодарили: 0 раз.
More info,

i tried only

GB5T-14G376-AA
GB5T-14G374-CB or 1U5T-14G374-DA or HB5T-14G374-CA

all get the same error.

Set new address failed.
Failed to programming flash! Error: Conditions not Correct [0x22]

I tried the other files seperate with the boatloader and they go without a problem.
Не в сети
Johoo
Сообщения: 10
Зарегистрирован: 24 ноя 2016, 09:57
Благодарил (а): 1 раз. Поблагодарили: 0 раз.
@kroligoff do you have a solution/suggestion for me?
Аватара пользователя
Не в сети
kroligoff
Сообщения: 1341
Зарегистрирован: 16 янв 2013, 10:38
Благодарил (а): 22 раз. Поблагодарили: 188 раз.
Conditions not Correct [0x22] give error if not have ignition , low voltage or other issue who not give access to programming mode
Не в сети
Johoo
Сообщения: 10
Зарегистрирован: 24 ноя 2016, 09:57
Благодарил (а): 1 раз. Поблагодарили: 0 раз.
Batterie is only 2 years old. I always charge the batterie 100% full with a Ctek charger before i programm with UCDS.

I have keyless entry.

Strange thing also is,

this combination gets the error.

GB5T-14G376-AA
GB5T-14G374-CB or 1U5T-14G374-DA or HB5T-14G374-CA


this combination, programming works

GB5T-14G376-AA
1U5T-14G375-HA or GB5T-14G379-AA or JB5T-14G379-BA

i tried enable sleep all modules on and off, makes no difference.
Не в сети
Jamie75
Сообщения: 7
Зарегистрирован: 16 ноя 2019, 01:13
Благодарил (а): 0 раз. Поблагодарили: 0 раз.
has anyone else had this issue? i need to flash my APIM with the same files a @johoo and don't want to wind up with a mess

need to use the below

GB5T-14G376-AA
1U5T-14G374-DA
1U5T-14G375-DA
GB5T-14G379-AA
JB5T-14G379-BA
Не в сети
silverstreak2006
Сообщения: 9
Зарегистрирован: 05 янв 2020, 15:32
Благодарил (а): 1 раз. Поблагодарили: 0 раз.
Probably dead module.

Вернуться в Technical Support

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 2