uploading VBF files failed IPMA [SOLVED]

[mondeo2015]

Updated moduls with UCDS, using update wizard. Since the update, I have a number of errors, options that don't work anymore. Keyless entry, traffic sign recog, lane assist and some other.
Most of the disaiblings are due to malfunction of the IPMA module, I think?
I even tried to upload and install the file via vbf loader. SBL + 19/24/81/82 , SBL + 19;SBL + 24;SBL + 81;SBL + 82; SBL + 19/24; SBL + 81/82. No succes! What am I doing wrong here? Am I installing "old" software or what?
What is the latest SF-update for IPMA for WF0EXXWPCEEG29850?
Thank you

[kroligoff]

Try
SBL: DA5T-14G021-BA
1: DS7T-14G019-EM
2: HS7T-14G082-EB
3: DS7T-14G024-EJ

[sev611]

if you have malfunktion in lane keeping and recognition of traffic sign then you have to do a calibration of front camera
it takes about 5 minutes to do

[mondeo2015]

I finally succeeded! IPMA is back. Tomorrow, indeed, camera-calibration.
I really had to re-activate IPMA, because not listed anymore.
Now, I know I have succeeded, because traffic sign recog, lane assist are back on the cluster and auto-beam is listed again under" lightning"

[dragunov]

Tell me how u fixed this?

[mondeo2015]

VBF-loader:

1. SBL DA5T-14G021-BA
+DS7T-14G019-EM
+DS7T-14G024-EJ

2. SBL DA5T-14G021-BA
+HS7T-14G082-EB

3. SBL DA5T-14G021-BA
+HS7T-14G081- EB

May vary

[dragunov]

What did u use?

[mondeo2015]

1. SBL DA5T-14G021-BA
+DS7T-14G019-EM
+DS7T-14G024-EJ

2. SBL DA5T-14G021-BA
+HS7T-14G082-EB

3. SBL DA5T-14G021-BA
+HS7T-14G081- EB

[Smoky334]

Hello,

This morning I was updating a few modules through the UCDS update wizzard. All went fine until I updated the IPMA module and the car battery died on me even with a battery charger attached. So now the IPMA is not found anymore. Can anyone provide me the numbers of the files I need to download so I can use the UCDS VBF File Loader? If this is the best option to get it working again?

Thanks!

[mondeo2015]

Hi, you can use the above mentioned files:
VBF-loader:

1. SBL DA5T-14G021-BA
+DS7T-14G019-EM
+DS7T-14G024-EJ

2. SBL DA5T-14G021-BA
+HS7T-14G082-EB

3. SBL DA5T-14G021-BA
+HS7T-14G081- EB



activate "deep sleep" modules.....
activate "dead modules"

I've made the fault once(battery), but not twice. For now, I ALWAYS let the engine run whilst opdating, especially the long ones....never had any trouble doing that.
This is the ONLY way to get it working again....

[dragunov]

Never let the engine run, if not, there is no control over the engine

[Diamondear]

As soon as I have some time, I will perform the last update to the IPMA module.

But I would have a question to ask those who have already done so.
According to you it is normal how the list of the Current Software Part appears?
It looks as if UCDS could not read the form correctly.

Thank you

[Diamondear]

IPMA module update completed successfully.
No calibration of the camera was necessary.
No errors in the DTC.

[mm32]

IPMA module update completed successfully.
No calibration of the camera was necessary.
No errors in the DTC.

The sequence on the list (from Your picture) is good?
You had change somethings or You only push the button " START UPDATE " ?

[Diamondear]

@mm32

Hi,
The sequence you see in the picture is the correct one.
Go ahead and do not be afraid.