Мондео 5 Штатный автозапуск
-
kostik1485
- Сообщения: 3
- Зарегистрирован: 05 май 2015, 18:56
Мондео 5 Штатный автозапуск
Добрый день, подскажите как активировать штатный авто запуск на мондео 5 2016г, ключик заказали прописали у дилера в аварийном слоте его видит но с кнопок машина не управляется, брелоки все 434 мгц, в бсм и щитке вроде все что с авто запуском связано активировали (в меню щитка появилось меню запуска)
-
Vadimsss
- Сообщения: 5
- Зарегистрирован: 10 авг 2017, 13:16
Re: Мондео 5 Штатный автозапуск
На форуме форскана для фордов находил такой мануал, может поможет. В конце написано, что нужно сбросить модули, после этого
старые ключи станут работать только в аварийном слоте.
Remote Start
To activate Remote Start, first you need a new key fob with start button (part # DS7T-15K601-EF or newer for Mondeo with 433 MHz).
Programming keys
Determine the backup slot of the passive key.
Place the first programmed key in the backup slot. Press the START / STOP button.
Wait for 5 seconds, then press the START / STOP button.
Extract the first programmed passive key.
Within 10 seconds, place the second programmed passive key in the backup slot, then press the START / STOP button.
Wait for 5 seconds, then press the STOP-STOP button.
Extract the second programmed key.
Wait 5 seconds, then place the unprogrammed passive key in the backup slot and press the START / STOP button.
After the procedure is completed, if everything was done correctly, the engine will be started if the passive key is in the backup slot, the buttons will not work on the key.
Now use Forscan to change the asbuilt-data
IPC
720-02-02 0000 X000
add 1 = Passenger Seat
add 2 = RS on
add 4 = Driver Seat
add 8 = Climate Settings
720-02-02 0000 0X00
add 8 = Rear Defrost
add 4 = Heatet Steering Wheel
Brings up options in settings-menu
BCM
726-22-02 000X 0000 0000
add 1 = RS on
RTM
751-01-01 0X00 0000
set to 1 = RS off
set to 2 = RS on
After writing back the new values, you have to do a manual reset of the three modules (or remove battery for a while). After reseting RTM the original keys won't work anymore (beside in backup slot), but now you can use the new key to open / close / start and remote start the car.
To switch back to default keys, just set RTM back to 1 and do a reset.
старые ключи станут работать только в аварийном слоте.
Remote Start
To activate Remote Start, first you need a new key fob with start button (part # DS7T-15K601-EF or newer for Mondeo with 433 MHz).
Programming keys
Determine the backup slot of the passive key.
Place the first programmed key in the backup slot. Press the START / STOP button.
Wait for 5 seconds, then press the START / STOP button.
Extract the first programmed passive key.
Within 10 seconds, place the second programmed passive key in the backup slot, then press the START / STOP button.
Wait for 5 seconds, then press the STOP-STOP button.
Extract the second programmed key.
Wait 5 seconds, then place the unprogrammed passive key in the backup slot and press the START / STOP button.
After the procedure is completed, if everything was done correctly, the engine will be started if the passive key is in the backup slot, the buttons will not work on the key.
Now use Forscan to change the asbuilt-data
IPC
720-02-02 0000 X000
add 1 = Passenger Seat
add 2 = RS on
add 4 = Driver Seat
add 8 = Climate Settings
720-02-02 0000 0X00
add 8 = Rear Defrost
add 4 = Heatet Steering Wheel
Brings up options in settings-menu
BCM
726-22-02 000X 0000 0000
add 1 = RS on
RTM
751-01-01 0X00 0000
set to 1 = RS off
set to 2 = RS on
After writing back the new values, you have to do a manual reset of the three modules (or remove battery for a while). After reseting RTM the original keys won't work anymore (beside in backup slot), but now you can use the new key to open / close / start and remote start the car.
To switch back to default keys, just set RTM back to 1 and do a reset.