PSCM Module (Focus 2017)

[lamberps]

Hi,

I posted this in the main forum but that may have been the wrong place.

I'm trying to turn off PDC (Pull Drift Control) but having issues.

When reading the PSCM module with security set to auto I get invalid key x35. If I set to no security I can read the module.

I can't write to the module with auto or no security, any ideas ?

Thanks !

[Kalehof]

I use the following setting:
To read: extended diagnostic and w/o security
To write: extended diagnostic and programming level

This worked so far on every car I turned PDC of in the PCSM

[Benutzername]

On my car it doesn´t work.

Reading on "auto" give the same error as lamberpss.

Reading/Writing with
"To read: extended diagnostic and w/o security ..... To write: extended diagnostic and programming level "

Give´s no errors. But it didn´t change anything.

If I re-read the config it`s still enable

[Kalehof]

Will check again end of the week, when I’m back home.
Sucsefully turnes it off on over 15cars so normally it should work. But let me check again

[Benutzername]

So, I tried it today again.

On my Car it doesn´t change the setting



Did it worked on your Car lamberps?


II use the following setting:
To read: extended diagnostic and w/o security
To write: extended diagnostic and programming level

And tried other settings, too...

Reseted the module afterwards or didn´t resest it...
It says changes written, but if i reload, their all the same and PDC is always enabled.

[lamberps]

Same here. UCDS says it successfully updated the module, but if you re-read the setting still says its enabled.

I've tried different combinations of security mode, etc. and tried module resets but nothing works.

[Benutzername]

Somebody wrote that You can disable pdc in asbuilt.

I'll search this, next time I have time to play....

[Benutzername]

searched for PDC in the asbuilt, but didn't find it.

It would be real nice to disable the PDC for testing agein, but it seems, it doesn't work with UCDS

[Artist]

On my car it doesn´t work.
Reading on "auto" give the same error as lamberpss.
Reading/Writing with
"To read: extended diagnostic and w/o security ..... To write: extended diagnostic and programming level "
Give´s no errors. But it didn´t change anything.
If I re-read the config it`s still enable

Try to check "M" Can write, it helped me with another problem ...

[Benutzername]

Today I tried again with MM-Can-Bus active.

It still doesn't work / change the settings.

I Think it's a bug in the UCDS Software

[lamberps]

Same here, I'd already tried with CAN-Bus enabled and it does nothing. Perhaps it's not supported but would be could to get a response from the UCDS team on this !

[kroligoff]

I use the following setting:
To read: extended diagnostic and w/o security
To write: extended diagnostic and programming level

This worked so far on every car I turned PDC of in the PCSM

Its Correct!

Today I tried again with MM-Can-Bus active.

It still doesn't work / change the settings.

I Think it's a bug in the UCDS Software

Its not bug.
Any modules PSCM cant change this parameters. In next version i add EEPROM read/write for PSCM

[Benutzername]

Its not bug.
Any modules PSCM cant change this parameters. In next version i add EEPROM read/write for PSCM

Thank for our quick answer.

Doyou know, when the next version will be released?

[Benutzername]

So, when will the new version be availible?
Or is there another way to get the PDC dissable and enable?

[kroligoff]

Problem already fixed, you can off
contact me over PM , i provide test version with update